Pipeclamp Bases and Brackets

Refine your results
17 products found
  • Grid view
  • List view
  • Large grid view
Buy More Save
M12 x 100 Ankerbolts (Thunderbolts) x 2

Ankerbolts M12 x 60 Galvanised (Thunderbolts) x 2

M12 x 60 Galvanised Ankerbolts (Thunderbolts). Suitable for fixing down handrail base plate fittings such as for 132, 144, 145, 232, 246, 247 & 251 (not for sizes 26.9mm/60.3mm). Sold in pairs.

  • £1.76 Ex VAT
131 Wall Plate

131 Wall Plate Key Clamp

With 4 countersunk holes, this fitting is ideal as a flange to terminate handrail to a wall or other similar application. This key clamp fitting may be used on structures where it is only required as a positional fixing.

  • £1.82 Ex VAT
Buy More Save
M12 x 100 Galvanised Through Bolts x 2

M12 x 100 Galvanised Through Bolts x 2

M12 x 100 Galvanised Through Bolts. Suitable for fixing down handrail base plate fittings such as for 132, 144, 145, 232, 246, 247 & 251 (not for sizes 26.9mm/60.3mm). Sold in pairs.

  • £1.82 Ex VAT
Buy More Save
M12 x 100 Ankerbolts (Thunderbolts) x 2

Ankerbolts M12 x 75 Galvanised (Thunderbolts) x 2

M12 x 75 Galvanised Ankerbolts (Thunderbolts). Suitable for fixing down handrail base plate fittings such as for 132, 144, 145, 232, 246, 247 & 251 (not for sizes 26.9mm/60.3mm). Sold in pairs.

  • £1.82 Ex VAT
Buy More Save
M12 x 100 Ankerbolts (Thunderbolts) x 2

Ankerbolts M12 x 100 Galvanised (Thunderbolts) x 2

M12 x 100 Galvanised Ankerbolts (Thunderbolts). Suitable for fixing down handrail base plate fittings such as for 132, 144, 145, 232, 246, 247 & 251 (not for sizes 26.9mm/60.3mm). Sold in pairs.

  • £1.95 Ex VAT
Buy More Save
M16 x 100 Galvanised Through Bolts x 2

M16 x 100 Galvanised Through Bolts x 2

M16 x 100 Galvanised Through Bolts. Suitable for fixing down handrail tubular standards and also 132 pipeclamp base plate fittings in size 5 (60.3mm). Sold in pairs.

  • £1.95 Ex VAT
143 Wall Mounted Handrail Bracket

143 Wall Mounted Handrail Bracket Key Clamp

Wall mounting bracket for handrails. Can also be used to tie back structures to wall or to hold kicking plates on a guardrail. This Key Clamp fitting has countersunk holes and is not recommended as a structural fixing. This fitting has no ability to join tubes.

  • From £2.37 Ex VAT
Buy More Save
132 Base Plate

132 Base Plate Key Clamp

A structural base plate for all aspects of vertical post support. This key clamp fitting when used as a base plate for guardrailing should always be positioned with the holes across the line of the guardrail to give maximum strength. The holes in the base plate are large enough to enable the use of mechanical or chemical anchor fixings.

  • From £3.32 Ex VAT
146 Flush Side Palm Fixing

146 Structural Flush Side Palm Fixing Key Clamp

Key Clamp Structural flush side palm base fixing for fixing guardrailing to wall steps or ramps etc. The flush design enables posts to be tight to the structure. The tube is unable to pass through the fitting. Should this be required then the base must be reamed out. If the base is reamed out the bottom fixing will become redundant.

  • From £3.65 Ex VAT
144 Structural Offset Side Palm Fixing

144 Structural Offset Side Palm Fixing Key Clamp

Key Clamp Structural offset side palm base fixing for fixing guardrailing to walls, steps, ramps, etc. The tube is unable to pass through this fitting as supplied, should this be required then the base must be reamed out. Access to the top fixing is restricted. It is recommended that a threaded stud is fixed first with a maximum projection of 25mm.

  • From £4.76 Ex VAT
232 Slope Range Base

232 Slope Range Base Key Clamp

An adjustable structural base fitting for the vertical. The design of this Key Clamp fitting will only allow it to be installed in the correct plane. For correct orientation see details below.

  • From £5.92 Ex VAT
134 Ground Socket

134 Ground Socket Key Clamp

A ground socket cast into concrete which is flush to the finished ground level. The upright is held in place using the grubscrew but can easily be removed without leaving any obstructions.

  • From £6.68 Ex VAT
246 Horizontal Railing Base

246 Horizontal Railing Base Key Clamp

Designed to be interchangeable with traditional welded ball standard bases. Fixing holes suit a wide range of common mechanical and chemical masonry anchors.

  • From £8.02 Ex VAT
251 Slope Base Flange (30°-45°)

251 Slope Base Flange (30°- 45°) Key Clamp

Base flange for sloping sites, adjustable from 30° to 45°. As the fixing holes in the base cannot be fixed in line with the applied load, it is only intended for light loads or structures which are sufficiently supported by virtue of their design. Where a greater load is required, type 132 is normally used, with the upright tube bent to the required angle.

  • From £8.45 Ex VAT
252 Slope Base Flange (11°- 29°) Key Clamp

252 Slope Base Flange (11°- 29°) Key Clamp

Base flange for sloping sites, adjustable from 11° to 29°. As the fixing holes in the base cannot be fixed in line with the applied load, it is only intended for light loads or structures which are sufficiently supported by virtue of their design. Where a greater load is required, type 132 is normally used, with the upright tube bent to the required angle.

  • £9.30 Ex VAT
247 Base Flange with Toe Board Fixing

247 Base Flange with Toe Board Fixing Key Clamp

This Key Clamp fitting is a base flange with toe board attachment facility. This fitting is ideal as a base for the vertical on guardrails where the addition of a toe board or kicking flat is required.

  • From £12.69 Ex VAT
Close

1 item(s) added to your compare list